 |
| Search all USDA |
 |
|---|
|
Beefy Backpack Tree Marking Paint System
Technical Support Documents Cylinder Cleaning April 5, 2000 One of the most common questions asked of Catalina Cylinders is, "How do we clean aluminum cylinders which have been in service?" Catalina Cylinders has found the following cleaning practices to be effective in the cleaning of aluminum cylinders. The cleaning practices have been broken down into two groups, external and internal, with different types of conditions requiring cleaning listed under each group. External General In-service Soiling Wash with a dishwashing soap and rinse. Dry the cylinder after rinsing. Chipping Paint or Minor Corrosion Removal of loose paint and minor corrosion by-products by scrapping with a scrapper or putty knife is acceptable. If complete paint removal from a cylinder is desired, Catalina Cylinders recommends that paint be removed from aluminum cylinders by the use of paint strippers. Catalina Cylinders has found that gel-type strippers work well in removing old paint and do not remove metal from the cylinder when properly used. Use gel strippers that are compatible with aluminum. Take great care to ensure that the gel-type stripper does not enter the cylinder. Catalina Cylinders does not recommend cleaning of cylinders by means of sanding or abrasive blasting. Removal of paint or minor corrosion from a cylinder by sanding or abrasive blasting can also remove metal thus reducing the wall thickness of the cylinder and reducing the integrity of the cylinder. If sanding or abrasive blasting is used to clean a cylinder, the remaining wall thickness after sanding or abrasive blasting is complete must be checked by suitable means (i.e. a U.T. gauge) to guarantee the minimum remaining wall thickness is greater than the minimum design wall thickness. Catalina Cylinders strongly recommends against the use of any method of exposure to high heat (i.e. flame, oven, etc.), in excess of 265° F, for any amount of time in the removal of paint from aluminum cylinders. Internal Moisture and Light Soils Steam clean with soft water and blow dry with forced air if possible. If not possible, fill cylinder with hot soft water and tumble the cylinder for a few minutes. The hotter the temperature of the water introduced into the cylinder increases the capability of the hot cylinder to aid in the drying of the cylinder by evaporation. Follow the tumbling with hot soft water by 1 minute of forced air blow-drying. Always make sure the air used in blow-drying a cylinder is dry and free of contaminates (filtered). Drying the cylinder completely after cleaning is necessary to reduce the chance of corrosion from occurring. Grease, Oil and Lubricants Tumble the cylinder for 5 minutes with a solution of a small amount of dishwashing soap and hot soft water. Make sure the amount of solution is sufficient to wet the entire inside surface of the cylinder. Rinse the cylinder with hot soft water. Several rinses may be required to remove all the soapy solution. Repeat this sequence as often as needed. Drying the cylinder completely after cleaning is necessary to reduce the chance of corrosion from occurring. Odors For a few minutes wet the entire inside of the cylinder with a solution of baking soda and soft water, approximately ½ - 1 cup of baking soda to 1 gallon of water. Make sure the entire inside surface is wetted by the solution. Next, rinse the cylinder with soft water. Follow this with a few minutes of wetting the entire inside surface of the cylinder with a solution of vinegar and water, approximately on ¼ -1/2 cup of household vinegar to 1 gallon of water. Then rinse the cylinder completely with water until all odor of vinegar is gone. If original odor persists, repeat this operation as many times as necessary. Drying the cylinder completely after cleaning is necessary to reduce the chance of corrosion from occurring. Corrosion Tumble the cylinder with a slurry of aluminum oxide pellets and water. You may choose to add a little dishwashing soap to the slurry to aid in the cleaning process. The amount of water inside the cylinder should be sufficient enough to wet the entire inside surface of the cylinder. The amount of aluminum oxide pellets to be used is dependent on the condition of the cylinder. Start out with 1 cup of aluminum oxide pellets to 1 gallon of water and increase the amount of pellets as needed. Most corrosion is removed within 30 minutes of rotating the cylinder at 30 rpm. Always rinse and dry the cylinder after tumbling is complete. Drying the cylinder completely after cleaning is necessary to reduce the chance of corrosion from occurring. Please note that after all cleaning operations it is recommended that the cylinder be dried completely to reduce the chance of corrosion from occurring. |
 
|
